The HP LaserJet M140we driver download for Windows 11, Windows 10 (32-bit and 64-bit) is the HP LaserJet MFP M139w/M139we/M140w/M140we/M141w/M141we/M142w/M142we EasyStart Printer Setup Software – Offline Use Only, and for a Mac HP lists the package titled “Install HP app to complete setup and support”. This page lists HP’s official software for the HP LaserJet MFP M140we.

Recommended LaserJet M140we driver downloads
Files download directly from HP’s official servers. hpdrivers.net does not host or modify them.
Which Windows package does the LaserJet M140we driver need?
These are the main types of Windows package that HP lists specifically for the LaserJet MFP M139e-M142e:
- Firmware update (v20260530, Jul 23, 2026): updates the printer itself, not your PC.
- Full software solution (v54.3.5248, Feb 08, 2023, 186.1 MB): driver plus HP’s setup wizard and tools.
LaserJet M140we driver: all packages
LaserJet M140we driver for Windows
File details
File:M139-M142_Series_FW_Update-20260530.exeFile details
File:HPEasyStart-13.6.5-LJM139-M142_UWL_54_3_5248_1_Webpack.exeMac firmware utility for the LaserJet M140we
File details
File:M139-M142_Series_FW_Update-20260530.dmgScanning and OCR software
Setup tools and other software
LaserJet M140we driver for Linux
HP lists Linux support for this series through its HPLIP project, outside the regular download list: HP’s Linux printing page (HPLIP).
Which systems the LaserJet M140we driver supports
HP’s download list for the LaserJet M140we names Windows 11; Windows 10, 8.1, 8, 7 (32-bit and 64-bit); macOS 26, 15, 14, 13, 12, 11, 10.15, 10.14, 10.13, 10.12, Mac OS X 10.11, Mac OS X 10.10, Mac OS X 10.9, Mac OS X 10.8, Mac OS X 10.7, Mac OS X 10.6, Mac OS X 10.5; and Linux through HPLIP. For macOS 26, 15, 14, 13, 12, 11, setup runs through the HP app. For macOS 10.15, 10.14, 10.13, 10.12, Mac OS X 10.11, Mac OS X 10.10, Mac OS X 10.9, Mac OS X 10.8, Mac OS X 10.7, Mac OS X 10.6, Mac OS X 10.5, HP’s list has only the firmware utility.
HP’s specifications for the LaserJet MFP M139e-M142e series say Windows 7, 8 and 8.1 are not supported and that the full software solution is only for Windows 10 and newer. HP’s download list still shows some files for older versions.
Installing the LaserJet M140we driver
To install it, follow these steps.
- Choose the installer from the table above.
- Start it and follow the on-screen instructions.
- Join your Wi-Fi network or plug in USB when prompted.
- Print a test page to check the connection.
For step-by-step instructions, see our guide to installing an HP printer driver.
Firmware update 20260530 for the LaserJet M140we
For the LaserJet M140we, HP lists the HP LaserJet MFP M139we/M140we/M141we/M142we Printer Firmware Update Utility (not compatible with HP LaserJet MFP M139w Printer), version 20260530, released Jul 23, 2026. HP’s notes for it: USB Support for PSA Driver; Security updates; General improvements and bug fixes.
- Check your current firmware version first on the printer’s Configuration Page, and update only if it is older.
- Install the printer driver before running the update. HP’s utility needs it to reach the printer.
Specifications that matter for setup
Toner supplies HP lists for the LaserJet MFP M139e-M142e
HP’s specifications name these replacement supplies for the LaserJet MFP M139e-M142e:
- HP 141A Black LaserJet Toner Cartridge (~950 pages), W1410A
- HP 142A Black LaserJet Toner Cartridge (about 950 pages), W1420A
- HP 150A Black LaserJet Toner Cartridge (about 975 pages), W1500A
What comes in the box
HP lists these items with the LaserJet MFP M139e-M142e:
- Printer
- Power cord
- Toner Cartridge
- Setup Poster
- Reference Guide
- Warranty Guide
Paper handling and hardware details
Values below are HP’s published figures for the LaserJet MFP M139e-M142e series, which the LaserJet M140we belongs to.
Connecting the printer to Wi-Fi with HP Smart
HP Smart (HP’s current download list calls it the HP app) is the method HP’s M139-M142 guide lists first for the wireless models, so start there. Install the app on a computer or mobile device first, because the app adds the printer to your network.
- Check that the computer or mobile device is on your Wi-Fi network. On a mobile device, also turn on Bluetooth and location services.
- Turn the printer’s Wi-Fi on if it is off.
- Restore the printer’s network settings if it is no longer in wireless setup mode.
- Open HP Smart and tap the plus icon or Add Printer, then choose your printer. Allow the Bluetooth and location permissions when asked.
- Follow the instructions until the printer is added to the network.
- Create or sign in to an HP account and register the printer when prompted.
HP Smart uses Bluetooth for setup. Printing over Bluetooth is not supported. When the connection succeeds, the wireless light stops blinking and stays on.
The wireless button and light
The Wireless button has three jobs. A short press turns the wireless function on or off, and it sets up a Wi-Fi Direct connection. A long press starts a WPS connection. Together with Cancel, it also resets the network settings.
- When the light stays on, the wireless connection is stable.
- If it blinks, there is no wireless connection yet, or a WPS or Wi-Fi Direct setup is in progress.
- Whenever it blinks fast, the wireless connection has a problem.
To reset the network settings, press Cancel first if the printer is asleep and its Ready light is dim. Then hold the Wireless and Cancel buttons together for five seconds. The printer restarts, and a blinking wireless light means it is in setup mode again. After that, reconnect with HP Smart.
Connecting through the router’s WPS button
WPS works only when your router has a WPS button. If it does not, HP recommends HP Smart instead.
- Keep the router and the printer fairly close together.
- Before you press anything, make sure the printer is in wireless setup mode.
- Press the WPS button on the router.
- Within two minutes after that, hold the printer’s Wireless button for at least five seconds and release it.
- Wait while the printer connects, which can take up to two minutes. The wireless light stops blinking and stays on when the link is ready.
- Open HP Smart, add the printer and register it when prompted.
If the display shows Er/61, the WPS connection failed. Press Cancel to carry on and try the connection again. When the error stays, connect with HP Smart instead.
Switching between USB and wireless
On Windows 10 and macOS, HP’s guide uses HP Smart to change the connection in either direction.
To go from USB to wireless, unplug the USB cable before you do anything else. Next, check that your device is on the Wi-Fi network, and turn on Bluetooth and location services if it is a mobile device. Make sure the printer’s Wi-Fi is on and that the printer is in setup mode. Then open HP Smart, create or sign in to an account when asked and follow the screens to join the network.
When you go from wireless back to USB, plug the USB cable into the printer and the computer. Open HP Smart on the computer, tap the plus icon or Add Printer, and choose the printer. Finally, follow the instructions and register it if prompted.
A checklist for wireless problems
Work through these checks one by one.
- Before anything else, confirm that the printer and router are on and that the printer’s wireless radio is enabled.
- Check the SSID: wake the printer with Cancel, then hold Resume for five seconds to print a page that lists it.
- Verify the security information, and run the wireless setup again if it is wrong.
- On a WPA network, check that the printer uses the same encryption method (AES or TKIP) as the router.
- Keep the printer within range. While the exact range varies, on most networks it should be within 30 m of the router.
- Clear large metal objects from the path. Make sure no metal or concrete posts or walls stand between the printer and the access point.
- Keep motors, cordless phones, security cameras and some Bluetooth devices away, because they can interfere with the signal.
- Confirm that the driver is installed, the right port is selected and both devices share one network.
- If you use a Mac, make sure the router supports Bonjour.
Solving common wireless faults
- No printing after setup: check that the printer is on and ready, then turn off third-party firewalls. If it still fails, restart the computer and confirm that the network works.
- Firewall blocking: update the firewall first. When it asks for access, allow the printer program. Alternatively, turn the third-party firewall off during the wireless install and enable it afterwards.
- Moved printer or router: print a configuration page, then compare its SSID with the one in the computer’s printer settings. If they differ, the devices are on different networks, so set up the wireless connection again.
- Second computer cannot connect: check that the computer is in range and that nothing blocks the signal. Also confirm the printer is ready, that no more than five Wi-Fi Direct users are connected at once, and turn off any third-party firewall on that computer.
- VPN dropout: you normally cannot use a VPN and another network at once. After you disconnect the VPN, rejoin both devices to the wireless network.
- Missing network: check that the router is on. The network may be hidden, but you can still connect to a hidden network.
- Dead network: try another device on it. You can also ping the router’s IP address from a command prompt. A round-trip time in the window means the network works.
Running the wireless diagnostic test
The report shows the wireless network status, the signal strength and the networks that the printer found. Run it when a connection fails. You can start it from the printer or from the embedded web server.
On the control panel, press Cancel first if the printer is asleep. Hold Resume and Wireless together for three seconds, and release them when the Ready light starts to blink.
In the embedded web server, open the Networking tab and check whether the Wireless configuration page has the On option selected. Then click Print Test Results to print the report.
Keep the devices away from large metal objects, microwave ovens and cordless phones, because they can disturb the signal. Large stone structures can absorb radio waves, so keep clear of them too. Finally, place the router at a central point in line of sight with the printer.
Similar models
This page covers the M140we only. The M141we, M139we and M142we have their own pages.